EPSM-10GX4 Overview
Sensor-heavy vehicles and robots move more data than one 10G uplink can carry, yet the switch still has to fit a small custom enclosure. The EPSM-10GX4 is the Layer 2+ build in the Diamond Systems EPSM-10GX4 series: a small Ethernet switch module with the switching core, packet memory and management software on board, so for many designs the carrier only needs magnetics, I/O connectors and an input voltage regulator.
The module provides 24 10/100/1000 copper ports with non-blocking wire-speed performance, 12 from PHYs on the module and 12 through QSGMII to a 12-port PHY on the carrier, plus four 10G SFI ports for SFP+ fiber or copper transceivers. Layer 2+ software handles 8K MAC addresses, 4K VLANs, 8K IPv4 and IPv6 multicast groups and jumbo frames at all speeds. Management runs through a web GUI over any port, a command-line interface over RS-232 and SNMP v1/v2c/v3.
Network features include RSTP and MSTP, IEEE 802.3ad link aggregation on Layer 2 to Layer 4 information, multicast and broadcast storm control, IEEE 802.1X and 8 priorities with 8 QoS queues per port; our guide to board-level Ethernet switch modules explains how a module and carrier split the work. Two 120-pin Samtec ERF5 connectors carry all power and data to the carrier; the first handles power, nine ports and the RS-232 interface, so designs of nine ports or fewer can use it alone, and the second adds the remaining copper ports, the QSGMII lanes and the four 10G ports. The EPSM-10GX4-L3 adds Layer 3 routing, and the EPSM-10GX4-1588 is the PTP-ready Layer 3 build.
The module takes 5 V DC ±5% from the carrier and draws up to 20 W with all ports active. It runs from -40 to +85 °C with Diamond’s heat sink or heat spreader, the spreader suiting enclosures that can take heat through a wall. MIL-STD-202G shock and vibration resistance, as Diamond states it, suits vehicle use. Diamond provides a carrier design guide, development kits and a custom carrier board service.
EPSM-10GX4 Specifications
| Overview | |
|---|---|
| Brand & Model | Diamond Systems EPSM-10GX4 |
| Features | Compact Embedded Fanless Industrial Managed Ethernet Switch Rugged |
| Networking | |
| Switching Layer | Layer 2+ |
| Switch Type | Managed |
| Ethernet Ports | 24x 10/100/1000 BASE-TX [Board] |
| Number of Ethernet Ports | 24x Ethernet Ports |
| Number of Fiber Ports | 4x 10G [SFI] |
| Networking Standards | IEEE 802.1D Spanning Tree Protocol IEEE 802.1Q VLAN IEEE 802.1s Multiple Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1X Port-Based Network Access Control IEEE 802.3 10BaseTx Ethernet IEEE 802.3ab 1000BaseTx Gigabit Ethernet IEEE 802.3ad Link Aggregation IEEE 802.3ae 10 Gigabit Fiber IEEE 802.3u 100BaseTx Fast Ethernet |
| Power | |
| Power Input | 5V DC [Board] |
| Environmental Conditions | |
| Operating Temperature | -40°C to 85°C [-40°F to 185°F] |
| Certification | RoHS |
| Mechanical Properties | |
| Weight | 85 g (3.0 oz) |
| Dimensions | 84mm x 55mm (3.31" x 2.17") |
- EPSM-10GX4 Datasheet Download
| Number of Ports | 24 10/100/1000Mbps Ethernet ports with non-blocking wire-speed performance |
| 4 10G SFI ports for fiber or copper transceivers | |
| Magnetics and 10G transceivers required on carrier board | |
| Implementation | 12 PHYs integrated on main board; QSGMII signals for additional 12-port PHY on carrier board |
| On-board Memory | 4MB packet memory |
| Network Management | SNMP v1/v2c/v3; Web GUI and command line interface (CLI) |
| Power Management | ActiPHY and PerfectReach power management reduce power for shorter cable lengths and shut down power to disconnected ports |
| Serial Port | 1 serial port for host interface; RS-232 transceiver required on carrier board |
| Indicator lights | Serial data stream provided for 2 LEDs per port; decoder logic required on carrier board |
| Form Factor | 55x84mm / 2.17×3.31” (Same as COM Express Type 10) |
| Interconnect | Dual Samtec ERF5 series connectors, 120 pins each, 10mm board to board spacing |
| Input voltage | 5VDC +/-5% |
| Power consumption | 20W max, all ports active |
| Operating temperature | -40 to +85°C with DSC-provided heat sink or heat spreader |
| Cooling | Heat sink, 55x84mm, 16.6mm height |
| Heat spreader, 55x104mm, 7.6mm height | |
| Weight | 85G / 3.0 oz |
| Rohs | Compliant |
Official Diamond Systems USA Distributor
Things Embedded is an official Diamond Systems USA distributor, supplying the EPSM-10GX4 for USA robotics, defense and autonomous vehicle programs. Within the Diamond range the EPS-24G4X puts this switch on a complete 3.5 inch board with latching connectors and SFP+ sockets, and the EPSM-10GX is the module with two 10G ports.
As a module you integrate yourself, the EPSM-10GX4 sits among our Ethernet switch modules, our embedded Ethernet switches and our wider range of Ethernet switches. Where a custom carrier needs four 10G uplinks beside 24 gigabit ports and Layer 2+ management is enough, this is the model to specify.
Consult. Design. Integrate.
Things Embedded is a leading USA supplier of industrial computing and edge AI systems. We combine technical expertise with a collaborative approach to deliver optimal solutions for your application. Whether it’s an off-the-shelf platform or a custom design, we stay at the forefront of the latest technologies to ensure your success at the edge. Our team works closely with you from concept through deployment, providing guidance, engineering support, and integration expertise every step of the way.
Connect with our solutions experts today to review your requirements and find the ideal solution fit for your application.